Hogtunes 4 Channel RoadGlide Amplifier Adaptor Plate Bedienungsanleitung PDF herunterladen

RG 40.4 Adaptor Installation Instructions

Fig 1.1: NCA 40.4 Amp

positioned on adaptor plate

With the amp mounted to the plate, take one half of the supplied “hook and loop” adhesive” and apply to the back of

the plate. Take the other half of adhesive and apply to the brake side

inner fairing. Note: adhesives will work better

on clean surfaces, and at room temperature!

Line the amp up as in Fig 1.2 or 2.2 and “stick” the amp in place by joining both halves of the adhesive together.

When re-mounting the outer fairing to the bike, the bolts that hold the front turn signal on will secure the plate in

place even though the “hook and loop” adhesive does most of the work.

Go back to your amplifier Install manual to start wiring the amplifier.

IMPORTANT: If installing an NCA 40.4

,the wire harnesses that came in your original amp box are too short for Road

Glides. Please make sure to use the RG labeled harnesses that came in the RG 40.4 Adaptor box!

IMPORTANT:

If installing a NCA 70.2, you will use the harnesses that came with your amp.

Note: The wire harness passes from the fairing onto the bike through a rectangular opening where factory wires pass

through. “Fishing” a small piece of wire through this opening first, taping the amps wires to it, and using the “fish” to

pull these wires through should reduce install time.

Harley-Davidson, Electra Glide, Road Glide, Street Glide, Ultra Classic, and Tour-Pak are Trademarks, and/or Registered Trademarks of

Harley-Davidson, Inc., Milwaukee, Wisconsin, USA, and if Used or Implied are for Reference Only.

There is No Affiliation Between Harley-Davidson, Inc., and Hogtunes Inc.

Fig 1.2: NCA 40.4 Amp and

adaptor correctly installed

Hogtunes Inc., Unit 14 - 70 Ellis Drive, Barrie, Ontario, Canada, L4N-8Z3

Tel: (705) - 719-6361 Email: info@hogtunes.com

www.hogtunes.com

The RG 40.4 Adaptor plate properly installs a Hogtunes NCA 40.4

amplifier in Road Glides and is also used to mount a

Hogtunes NCA 70.2 in the same location.

If Installing a Hogtunes NCA 40.4

Using the same orientation as in Fig 1.1, attach the

amp to the plate using the supplied screws. The

screws will go through the plate and enter holes

on the underside of the amplifier.

If Installing a Hogtunes NCA 70.2

Using the supplied nuts and screws, attach the ampli-

fier to the black steel plate as shown in Fig 2.1

Make

sure to have the screws come through from under-

neath the plate. The supplied nuts are self locking,

but a thread adhesive material may be a good idea.

Fig 2.1: NCA 70.2 Amp

positioned on adaptor plate

Fig 2.2:

NCA 70.2 Amp and

adaptor correctly installed

Inhaltsverzeichnis

Seite 1

RG 40.4 Adaptor Installation Instructions Fig 1.1: NCA 40.4 Amp positioned on adaptor plate With the amp mounted to the plate, take one h

Kommentare zu diesen Handbüchern

Keine Kommentare

Hogtunes 4 Channel RoadGlide Amplifier Adaptor Plate Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio-Zubehör Hogtunes 4 Channel RoadGlide Amplifier Adaptor Plate herunter. Hogtunes 4 Channel RoadGlide Amplifier Adaptor Plate User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio-Zubehör Hogtunes 4 Channel RoadGlide Amplifier Adaptor Plate